FS: Fabrication Material Clear-out!! SS304 tube & pipe, Alum bends, etc.

[brett]

I have a slew of fabrication material that needs to go (I am back in school and money will be tight). Please make reasonable offers. For the quality you will be hard pressed to find better prices, if you do, shoot me an offer. Thanks!

4" Material:

• (3) 4" dia, 4" CLR (tight radius/bend), SS304, 90deg elbow w/12" leg on one side - $45/each

3.5" Material (slightly used):

• 3.5" flex bellow - $25
• (1) 3.5" dia, 5.25 CLR, 180deg U-bend w/8" legs - $40
• (2) 3.5" dia, 5.25 CLR SS304, 90deg elbows w/6" legs - $40/each
• 8 ft, 3.5" dia straight, SS304 - $18/ft

3" Material:

• (2) 3" dia, 3" CLR (tight radius/bend) SS304, 90deg elbows w/6" legs - $35/each
• (2) 3" dia, 4.5" CLR SS304, 90deg elbows w/6" legs - $22/each
• (7) 3" dia, 4.5" CLR 6061 aluminum, 90deg elbow w/6" legs - $15/each

2.5" Material

• (10) 2.5" dia, 3.75 CLR SS304, 90deg elbows w/6" legs - $20/each

2.25" Material

• 8 ft, 2.25" dia, straight, SS304 - $12/ft

Other:

• (25) 2.5" to 3" weld-on transitions, CNC machined, mild steel - $15/each
• TONS of manifold pipe: 1.5" schedule 40 SS304 pipe, butt-weld fittings (T's, 45deg, 90deg, straight). Let me know what you need. We used these on all of our manifolds and do many other fabricators. Prices vary between $5-8/each, but will be cheap - I need to get rid of this stuff!!

Please let me know what you need. Thanks for looking and tell your friends. Please call or email (brett.kordenbrock@gmail.com) as I hardly check the site or call, I am up in Columbus now.

Brett
513.205.2706

[ForceFed]

What Guage is the 4'' Piping?

[brett]

all material is 16ga, besides the pipe (which is schedule 40). Better pricing with bulk purchases too. Thanks,

brett

[VtecFreePrelude]

[*]TONS of manifold pipe: 1.5" schedule 40 SS304 pipe, butt-weld fittings (T's, 45deg, 90deg, straight). Let me know what you need. We used these on all of our manifolds and do many other fabricators. Prices vary between $5-8/each, but will be cheap - I need to get rid of this stuff!![/LIST]Please let me know what you need. Thanks for looking and tell your friends. Please call or email (brett.kordenbrock@gmail.com) as I hardly check the site or call, I am up in Columbus now.

Brett
513.205.2706

i might want some of this...at least 12 90*s...and do you have any straight pieces?

[brett]

we have several feet of straight pipe which can be cut to length. let me know what you need. I am in columbus, so my father or brother will have to hook you up, but no worries, they know what they're doing. just give me a time when you will be by and I can have them help you out, preferred after 3:30pm. all material is located in colerain, near the end of kemper rd.

just give me a call and we'll set it up.

[brett]

Bump this up, WAY up. We still have most of it. I can arrange for pick up as I am up in Columbus. My father or brother will be happy to assist. Let me know, I am saving for Europe and need some cash money. Help me out!

brett

[Allmotorcrx]

Bump for Brett. I've bought some of the 3 inch stainless and a few v bands.. very nice things.
________
Extreme Q Vaporizor

[4DooR_SuprA]

Brett, I need some 3" exhaust pieces. I see you have some bends, but two different sizes listed. Which one could I use?

[Ether240]

Originally Posted by Allmotorcrx

Bump for Brett. I've bought some of the 3 inch stainless and a few v bands.. very nice things.

that was a classic trip to his house in the smoking civic seth!

[brett]

Originally Posted by 4DooR_SuprA

Brett, I need some 3" exhaust pieces. I see you have some bends, but two different sizes listed. Which one could I use?

You could use either. The standard radius (4.5" CLR) usually works just fine for exhausts. the tight radius (3") can be advantageous in tight spaces, etc. Let me know.

brett